Top-flite TOPA1010 Bedienungsanleitung

WARRANTY...Top Flite®Models guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warrantydoes

❏ 6. Adjust the clevis on the flap pushrod so theflaps will be centered when the bell crank is neutral.Hint: The jigs you used to align the flaps can

LANDING GEAR INSTALLATIONInstall the Main Gear❏❏1. Locate the 5/32" [4mm] landing gear wire.❏❏2. Slide a 5/32" [4mm] wheel collar over theax

Install the Tail Gear❏ 1. Locate the 5/64" [2mm] tailgear wire and thesmall wheel collar.❏ 2. Mount the tail wheel to the pre-bent tail gearwire

FUEL TANK INSTALLATIONAssemble the Fuel Tank❏ 1. Remove the rubber stopper from the fuel tank.The hardware for the fuel tank is located inside of it.S

❏ 3. Cut 4"[102mm] and 3" [77mm] lengths of fueltubing. Connect the shorter length to the carburetorand the fuel line. The longer piece conn

❏ 2. Be certain the model is clean. Prepare adishpan or small bucket with a mixture of liquid dishsoap and warm water–about 1/2 teaspoon of soapper ga

As a general guideline, positioning the leadouts furtheraft makes plane pull harder on lines (for windy days),but also makes plane “handle” or react a

CHECKLIST❏ 1.Make sure areas exposed to fuel or exhaustresidue have been fuel proofed.❏ 2. Check the C.G. according to the measurementsand procedure p

pilots should control the model by keeping their armsstraight and bending at the elbow with little or no wristmovement. Later, when they become moreex

- 19 -AMA STUNT MANEUVERSHere are some of the AMA Stunt Maneuvers. Referto the AMA Rule Book for full descriptions.TakeoffReverse WingoversConsecutive

TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . 2IMPORTANT SAFETY PRECAUTIONS . . . . . . . 2ENGINE & LINE RECOMMEND

FLIGHT LOGDATE COMMENTSStarted AssemblyFinished AssemblyFirst FlightFirst LoopFirst Inverted FlightFirst Wingover

In addition to joining a control line club, we stronglyrecommend you join the AMA (Academy of ModelAeronautics). AMA membership is required to fly atA

KIT INSPECTIONBefore starting to build, take an inventory of this kit tomake sure it is complete, and inspect the parts tomake sure they are of accept

- 5 -PARTS PHOTOGRAPHED1. Flaps2. Wing3. Horizontal Stabilizerwith Elevators4. Fuselage5. Fin6. Canopy7. Main Landing Gear (2)8. 2-1/2" [65mm] Ma

BUILDING INSTRUCTIONSAssemble the Main Wing❏ 1. Locate the 4" [102mm] Flap Joiner Wire. Thereis a notch in the trailing edge (TE) of the wing sad

❏ 6. Mix up a batch of 30-minute epoxy. Slide the wingmost of the way into the fuselage. Apply epoxy to theinside of the wing saddle and to the wing w

Attach the Elevators❏ 1. Locate the Elevator Joiner Wire and the twoelevator halves.❏ 2. Remove the covering from the precut groove inthe LE of the el

Install the Flaps ❏ 1.Without using any glue, test fit the flap to the joinerwire and install 4 hinges. If necessary, use a hobbyknife to enlarge any